2nd Bench Scale ISR Study & £1.7M Placing

JORC Code explanation

Commentary

Sampling techniques

·    Nature and quality of sampling (eg cut channels, random chips, or specific specialised industry standard measurement tools appropriate to the minerals under investigation, such as down hole gamma sondes, or handheld XRF instruments, etc). These examples should not be taken as limiting the broad meaning of sampling.

·    Include reference to measures taken to ensure sample representivity and the appropriate calibration of any measurement tools or systems used.

·    Aspects of the determination of mineralisation that are Material to the Public Report.

·    In cases where 'industry standard' work has been done this would be relatively simple (eg 'reverse circulation drilling was used to obtain 1 m samples from which 3 kg was pulverised to produce a 30 g charge for fire assay'). In other cases more explanation may be required, such as where there is coarse gold that has inherent sampling problems. Unusual commodities or mineralisation types (eg submarine nodules) may warrant disclosure of detailed information.

2024

SONIC

·      Core was scanned by a SciAps X555 pXRF to determine sample intervals. Intervals through mineralized zones were taken at 10cm. Through waste, sample intervals were lengthened to 50cm. Core was halved by knife cutting. XRF scan locations were taken on an inner surface of the core to ensure readings were taken on fresh sample faces.

Full core samples were submitted to Australian Nuclear Science and Technology Organisation (ANSTO), Sydney for XRF analysis and to ALS Geochemistry Laboratory (Brisbane) on behalf of ANSTO for lithium tetraborate digest ICP-MS. The core was split in half along the vertical axis, and one half further split into 10 even fractions along the length of the half-core. Additional sub-sampling, homogenisation and drying steps were performed to generate ~260 g (dry equivalent) samples for head assay according to the laboratory internal protocols.

Drilling techniques

·    Drill type (eg core, reverse circulation, open-hole hammer, rotary air blast, auger, Bangka, sonic, etc) and details (eg core diameter, triple or standard tube, depth of diamond tails, face-sampling bit or other type, whether core is oriented and if so, by what method, etc).

2024

·      Sonic Core drilling completed Star Drilling using 4" core with a SDR12 drill rig. Holes were reamed to 6" or 8" to enable casing and screens to be installed

Drill sample recovery

·    Method of recording and assessing core and chip sample recoveries and results assessed.

·    Measures taken to maximise sample recovery and ensure representative nature of the samples.

·    Whether a relationship exists between sample recovery and grade and whether sample bias may have occurred due to preferential loss/gain of fine/coarse material.

Aircore & RC

·      Sample recovery was generally good. All samples were recorded for sample type, quality and contamination potential and entered within a sample log.

·      In general, sample recoveries were good with 10 kg for each 1 m interval being recovered from AC drilling.

·      No relationships between sample recovery and grade have been identified. 

·      RC drilling completed by Bullion Drilling Pty Ltd using 5 ¾" reverse circulation drilling techniques from a Schramm T685WS rig with an auxiliary compressor

·      Sample recovery for RC was generally good. All samples were recorded for sample type, quality and contamination potential and entered within a sample log.

·      In general, RC sample recoveries were good with 35-50 kg for each 1 m interval being recovered.

·      No relationships between sample recovery and grade have been identified.

Sonic Core

·      Sample recovery is considered excellent.

Logging

·    Whether core and chip samples have been geologically and geotechnically logged to a level of detail to support appropriate Mineral Resource estimation, mining studies and metallurgical studies.

·    Whether logging is qualitative or quantitative in nature. Core (or costean, channel, etc) photography.

·    The total length and percentage of the relevant intersections logged.

Sonic Core

·      Logging was carried out in detail, determining lithology and clay/ sand content. Logging intervals were lithology based with variable interval lengths.

·      All core drilled has been lithologically logged.

Sub-sampling techniques and sample preparation

·    If core, whether cut or sawn and whether quarter, half or all core taken.

·    If non-core, whether riffled, tube sampled, rotary split, etc and whether sampled wet or dry.

·    For all sample types, the nature, quality and appropriateness of the sample preparation technique.

·    Quality control procedures adopted for all sub-sampling stages to maximise representivity of samples.

·    Measures taken to ensure that the sampling is representative of the in situ material collected, including for instance results for field duplicate/second-half sampling.

·    Whether sample sizes are appropriate to the grain size of the material being sampled.

Sonic Drilling

·      Field duplicate samples were taken nominally every 1 in 25 samples where the sampled interval was quartered.

·      Blanks and Standards were submitted every 25 samples

·      Half core samples were taken where lab geochemistry sample were taken.

·      In holes where column leach test samples have been submitted, full core samples have been submitted over the test areas.

Quality of assay data and laboratory tests

·    The nature, quality and appropriateness of the assaying and laboratory procedures used and whether the technique is considered partial or total.

·    For geophysical tools, spectrometers, handheld XRF instruments, etc, the parameters used in determining the analysis including instrument make and model, reading times, calibrations factors applied and their derivation, etc.

·    Nature of quality control procedures adopted (eg standards, blanks, duplicates, external laboratory checks) and whether acceptable levels of accuracy (ie lack of bias) and precision have been established.

Sample Characterisation Test Work performed by the Australian Nuclear Science and Technology Organisation (ANSTO)

·      Full core samples were submitted to  Australian Nuclear Science and Technology Organisation (ANSTO), Sydney for preparation and analysis. The core was split in half along the vertical axis, and one half further split into 10 even fractions along the length of the half-core. Additional sub-sampling, homogenisation and drying steps were performed to generate ~260 g (dry equivalent) samples for head assay according to the laboratory internal protocols.

·      Multi element geochemistry of solid samples were analysed at ANSTO (Sydney) by XRF for the major gangue elements Al, Ca, Fe, K, Mg, Mn, Na, Ni, P, Si, S, and Zn.

·      Multi element geochemistry of solid samples were additionally analysed at ALS Geochemistry Laboratory (Brisbane) on behalf of ANSTO by lithium tetraborate digest  ICP-MS and analysed for Ce, Dy, Er, Eu, Gd, Ho, La, Lu, Nd, Pr,  Sm, Tb, Th, Tm, U, Y and Yb.

·      Reported assays are to acceptable levels of accuracy and precision.

·      Internal laboratory blanks, standards and repeats for rare earths indicated acceptable assay accuracy.

·      Samples retained for metallurgical analysis were immediately vacuum packed, nitrogen purged and refrigerated.

·      These samples were refrigerated throughout transport.

Metallurgical Leach Test Work performed by the Australian Nuclear Science and Technology Organisation (ANSTO)

·    ANSTO laboratories prepared ~80g samples for diagnostic leaches, a 443g sample for a slurry leach and a 660g sample for a column leach. Sub-samples were prepared from full cores according to the laboratory internal protocols. Diagnostic and slurry leaching were carried out in baffled leach vessels equipped with an overhead stirrer and applying a 0.5 M (NH4)2SO4 lixiviant solution, adjusted to the select pH using H2SO4.

·    1 M H2SO4 was utilised to maintain the test pH for the duration of the test, if necessary. The acid addition was measured.

·    Thief liquor samples were taken periodically.

·    At the completion of each test, the final pH was measured, the slurry was vacuum filtered to separate the primary filtrate.

·    The thief samples and primary filtrate were analysed as follows:

o  ICP-MS for Ce, Dy, Er, Eu, Gd, Ho, La, Lu, Mn, Nd, Pb, Pr, Sc, Sm, Tb, Th, Tm, U, Y, Yb.

o  ICP-OES for Al, Ca, Fe, K, Mg, Mn, Na, Si.

·    The water wash was stored but not analysed.

·    Column leaching was carried out in horizontal leaching column. The column was pressurised with nitrogen to 6 bar and submerged in a temperature controlled bath.

·    A 0.5 M (NH4)2SO4 lixiviant solution, adjusted to the select pH using H2SO4 was fed to the column at a controlled flowrate.

·    PLS collected from the end of the column was weighed, the SH and pH measured and the free acid concentration determined by titration. Liquor samples were taken from the collected PLS and analysed as follows:

o  ICP-MS for Ce, Dy, Er, Eu, Gd, Ho, La, Lu, Mn, Nd, Pb, Pr, Sc, Sm, Tb, Th, Tm, U, Y, Yb.

o  ICP-OES for Al, Ca, Fe, K, Mg, Mn, Na, Si.

·    The column leach test has been completed. Assays of the column are being taken to confirm PLS assays

Verification of sampling and assaying

·    The verification of significant intersections by either independent or alternative company personnel.

·    The use of twinned holes.

·    Documentation of primary data, data entry procedures, data verification, data storage (physical and electronic) protocols.

·    Discuss any adjustment to assay data.

·      Sampling data was recorded in field books, checked upon digitising and transferred to database.

·      Geological logging was undertaken digitally via the MX Deposit logging interface and synchronised to the database at least daily during the drill programme.

·      Compositing of assays was undertaken and reviewed by Cobra Resources staff.

·      Original copies of laboratory assay data are retained digitally on the Cobra Resources server for future reference.

·      Samples have been spatially verified through the use of Datamine and Leapfrog geological software for pre 2021 and post 2021 samples and assays.

·      Twinned drillholes from pre 2021 and post 2021 drill programmes showed acceptable spatial and grade repeatability.

·      Physical copies of field sampling books are retained by Cobra Resources for future reference.

·      Elevated pXRF grades were checked and re-tested where anomalous. pXRF grades are semi quantitative.

Location of data points

·    Accuracy and quality of surveys used to locate drill holes (collar and down-hole surveys), trenches, mine workings and other locations used in Mineral Resource estimation.

·    Specification of the grid system used.

·    Quality and adequacy of topographic control.

Pre 2021

·      Collar locations were pegged using DGPS to an accuracy of +/-0.5 m.

·      Downhole surveys have been completed for deeper RC and diamond drillholes

·      Collars have been picked up in a variety of coordinate systems but have all been converted to MGA 94 Zone 53. Collars have been spatially verified in the field.

·      Collar elevations were historically projected to a geophysical survey DTM. This survey has been adjusted to AHD using a Leica CS20 GNSS base and rover survey with a 0.05 cm accuracy. Collar points have been re-projected to the AHD adjusted topographical surface.

2021-onward

·      Collar locations were initially surveyed using a mobile phone utilising the Avenza Map app. Collar points recorded with a GPS horizontal accuracy within 5 m.

·      RC Collar locations were picked up using a Leica CS20 base and Rover with an instrument precision of 0.05 cm accuracy.

·      Locations are recorded in geodetic datum GDA 94 zone 53.

·      No downhole surveying was undertaken on AC holes. All holes were set up vertically and are assumed vertical.

·      RC holes have been down hole surveyed using a Reflex TN-14 true north seeking downhole survey tool or Reflex multishot

·      Downhole surveys were assessed for quality prior to export of data. Poor quality surveys were downgraded in the database to be excluded from export.

·      All surveys are corrected to MGA 94 Zone 53 within the MX Deposit database.

·      Cased collars of sonic drilling shall be surveyed before a mineral resource estimate

Data spacing and distribution

·    Data spacing for reporting of Exploration Results.

·    Whether the data spacing and distribution is sufficient to establish the degree of geological and grade continuity appropriate for the Mineral Resource and Ore Reserve estimation procedure(s) and classifications applied.

·    Whether sample compositing has been applied.

·     Drillhole spacing was designed on transects 50-80 m apart. Drillholes generally 50-60 m apart on these transects but up to 70 m apart.

·     Additional scouting holes were drilled opportunistically on existing tracks at spacings 25-150 m from previous drillholes.

·     Regional scouting holes are drilled at variable spacings designed to test structural concepts

·     Data spacing is considered adequate for a saprolite hosted rare earth Mineral Resource estimation.

·     No sample compositing has been applied

·     Sonic core holes were drilled at ~20m spacings in a wellfield configuration based on assumed permeability potential of the intersected geology.

Orientation of data in relation to geological structure

·    Whether the orientation of sampling achieves unbiased sampling of possible structures and the extent to which this is known, considering the deposit type.

·    If the relationship between the drilling orientation and the orientation of key mineralised structures is considered to have introduced a sampling bias, this should be assessed and reported if material.

·     Aircore and Sonic drill holes are vertical.

Sample security

·    The measures taken to ensure sample security.

·    Transport of samples to Adelaide was undertaken by a competent independent contractor. Samples were packaged in zip tied polyweave bags in bundles of 5 samples at the drill rig and transported in larger bulka bags by batch while being transported.

·    Refrigerated transport of samples to Sydney was undertaken by a competent independent contractor. Samples were double bagged, vacuum sealed, nitrogen purged and placed within PVC piping.

·    There is no suspicion of tampering of samples.

Audits or reviews

·    The results of any audits or reviews of sampling techniques and data.

·    No laboratory audit or review has been undertaken.

·    Genalysis Intertek and BV Laboratories Adelaide are NATA (National Association of Testing Authorities) accredited laboratory, recognition of their analytical competence.

JORC Code explanation

Commentary

Mineral tenement and land tenure status

·    Type, reference name/number, location and ownership including agreements or material issues with third parties such as joint ventures, partnerships, overriding royalties, native title interests, historical sites, wilderness or national park and environmental settings.

·    The security of the tenure held at the time of reporting along with any known impediments to obtaining a licence to operate in the area.

·    RC drilling occurred on EL 6131, currently owned 100% by Peninsula Resources limited, a wholly owned subsidiary of Andromeda Metals Limited.

·    Alcrest Royalties Australia Pty Ltd retains a 1.5% NSR royalty over future mineral production from licenses EL6001, EL5953, EL6131, EL6317 and EL6489.

·    Baggy Green, Clarke, Laker and the IOCG targets are located within Pinkawillinnie Conservation Park. Native Title Agreement has been negotiated with the NT Claimant and has been registered with the SA Government.

·    Aboriginal heritage surveys have been completed over the Baggy Green Prospect area, with no sites located in the immediate vicinity.

·    A Native Title Agreement is in place with the  Barngarla People.

Exploration done by other parties

·    Acknowledgment and appraisal of exploration by other parties.

·    On-ground exploration completed prior to Andromeda Metals' work was limited to 400 m spaced soil geochemistry completed by Newcrest Mining Limited over the Barns prospect.

·    Other than the flying of regional airborne geophysics and coarse spaced ground gravity, there has been no recorded exploration in the vicinity of the Baggy Green deposit prior to Andromeda Metals' work.

·    Paleochannel uranium exploration was undertaken by various parties in the 1980s and the 2010s around the Boland Prospect. Drilling was primarily rotary mud with downhole geophysical logging the primary interpretation method.

Geology

·    Deposit type, geological setting and style of mineralisation.

·    The gold and REE deposits are considered to be related to the structurally controlled basement weathering of epidote- pyrite alteration related to the 1590 Ma Hiltaba/GRV tectonothermal event.

·    Mineralisation has a spatial association with mafic intrusions/granodiorite alteration and is associated with metasomatic alteration of host rocks. Epidote alteration associated with gold mineralisation is REE enriched and believed to be the primary source.

·    Rare earth minerals occur within the saprolite horizon. XRD analysis by the CSIRO identifies kaolin and montmorillonite as the primary clay phases.

·    SEM analysis identified REE bearing mineral phases in hard rock:

·      Zircon, titanite, apatite, andradite and epidote.

·    SEM analyses identifies the following secondary mineral phases in saprock:

·      Monazite, bastanite, allanite and rutile.

·    Elevated phosphates at the base of saprock do not correlate to rare earth grade peaks.

·    Upper saprolite zones do not contain identifiable REE mineral phases, supporting that the REEs are adsorbed to clay particles.

·    Acidity testing by Cobra Resources supports that pH chemistry may act as a catalyst for Ionic and Colloidal adsorption.

·    REE mineral phase change with varying saprolite acidity and REE abundances support that a component of REE bursary is adsorbed to clays.

·    Palaeo drainage has been interpreted from historic drilling and re-interpretation of EM data that has generated a top of basement model. 

·    Ionic REE mineralisation is confirmed through metallurgical desorption testing where high recoveries are achieved at benign acidities (pH4-3) at ambient temperature.

·    Ionic REE mineralisation occurs in reduced clay intervals that contact both saprolite and permeable sand units. Mineralisation contains variable sand quantities that yield permeability and promote insitu recovery potentail

Drillhole Information

·    A summary of all information material to the understanding of the exploration results including a tabulation of the following information for all Material drill holes:

o  easting and northing of the drill hole collar

o  elevation or RL (Reduced Level - elevation above sea level in metres) of the drill hole collar

o  dip and azimuth of the hole

o  down hole length and interception depth

o  hole length.

·    If the exclusion of this information is justified on the basis that the information is not Material and this exclusion does not detract from the understanding of the report, the Competent Person should clearly explain why this is the case.

·    Exploration results being reported represent a small portion of the Boland target area. Coordinates for Wellfield drill holes are presented in Table 3.

Data aggregation methods

·    In reporting Exploration Results, weighting averaging techniques, maximum and/or minimum grade truncations (eg cutting of high grades) and cut-off grades are usually Material and should be stated.

·    Where aggregate intercepts incorporate short lengths of high grade results and longer lengths of low grade results, the procedure used for such aggregation should be stated and some typical examples of such aggregations should be shown in detail.

·    The assumptions used for any reporting of metal equivalent values should be clearly stated.

·    Reported summary intercepts are weighted averages based on length.

·    No maximum/ minimum grade cuts have been applied.

·    No metal equivalent values have been calculated.

·    Gold results are reported to a 0.3 g/t cut-off with a maximum of 2m internal dilution with a minimum grade of 0.1 g/t Au.

·    Rare earth element analyses were originally reported in elemental form and have been converted to relevant oxide concentrations in line with industry standards. Conversion factors tabulated below:

·   

·    The reporting of REE oxides is done so in accordance with industry standards with the following calculations applied:

·      TREO = La₂O₃ + CeO₂ + Pr₆O₁₁ + Nd₂O₃ + Sm₂O₃ + Eu₂O₃ + Gd₂O₃ + Tb₄O₇ + Dy₂O₃ + Ho₂O₃ + Er₂O₃ + Tm₂O₃ + Yb₂O₃ + Lu₂O₃ + Y₂O₃

·      CREO = Nd₂O₃ + Eu₂O₃ + Tb₄O₇ + Dy₂O₃ + Y₂O₃

·      LREO = La₂O₃ + CeO₂ + Pr₆O₁₁ + Nd₂O₃

·      HREO = Sm₂O₃ + Eu₂O₃ + Gd₂O₃ + Tb₄O₇ + Dy₂O₃ + Ho₂O₃ + Er₂O₃ + Tm₂O₃ + Yb₂O₃ + Lu₂O₃ + Y₂O₃

·      MREO = Nd₂O₃ + Pr₆O₁₁ + Tb₄O₇ + Dy₂O₃

·      NdPr = Nd₂O₃ + Pr₆O₁₁

·      TREO-Ce = TREO - CeO₂

·      % Nd = Nd₂O₃/ TREO

·      % Pr = Pr₆O₁₁/TREO

·      % Dy = Dy₂O₃/TREO

·      % HREO = HREO/TREO

·      % LREO = LREO/TREO

·      XRF results are used as an indication of potential grade only. Due to detection limits only a combined content of Ce, La, Nd, Pr & Y has been used. XRF grades have not been converted to oxide.

Relationship between mineralisation widths and intercept lengths

·    These relationships are particularly important in the reporting of Exploration Results.

·    If the geometry of the mineralisation with respect to the drill hole angle is known, its nature should be reported.

·    If it is not known and only the down hole lengths are reported, there should be a clear statement to this effect (eg 'down hole length, true width not known').

·    All reported intercepts at Boland are vertical and reflect true width intercepts.

·    Exploration results are not being reported for the Mineral Resource area.

Diagrams

·    Appropriate maps and sections (with scales) and tabulations of intercepts should be included for any significant discovery being reported These should include, but not be limited to a plan view of drill hole collar locations and appropriate sectional views.

·    Relevant diagrams have been included in the announcement.

·    Exploration results are not being reported for the Mineral Resources area.

Balanced reporting

·    Where comprehensive reporting of all Exploration Results is not practicable, representative reporting of both low and high grades and/or widths should be practiced to avoid misleading reporting of Exploration Results.

·    Not applicable - Mineral Resource and Exploration Target are defined.

·    Exploration results are not being reported for the Mineral Resource area.

Other substantive exploration data

·    Other exploration data, if meaningful and material, should be reported including (but not limited to): geological observations; geophysical survey results; geochemical survey results; bulk samples - size and method of treatment; metallurgical test results; bulk density, groundwater, geotechnical and rock characteristics; potential deleterious or contaminating substances.

·    Refer to previous announcements listed in RNS for reporting of REE results and metallurgical testing

Further work

·    The nature and scale of planned further work (eg tests for lateral extensions or depth extensions or large-scale step-out drilling).

·    Diagrams clearly highlighting the areas of possible extensions, including the main geological interpretations and future drilling areas, provided this information is not commercially sensitive.

·    The metallurgical testing reported in this announcement represents the second bench scale ISR study performed on a 20cm section of mineralized core

·    Future metallurgical testing will focus on producing PLS under leach conditions to conduct downstream bench-scale studies for impurity removal and product precipitation.

·    Hydrology, permeability and mineralogy studies are being performed on core samples.

·    Installed wells are being used to capture hydrology base line data to support a future infield pilot study.

·    Trace line tests shall be performed to emulate bench scale pore volumes.